MPL3115A2的arduino测试代码
/*Test_MPL3115A2-I2C.ino
This program for the Arduino (Uno) tests the library of procedures for
collecting readings from the Freescale MPL3115A2 altitude/barometric pressure/temperature
sensor.
This library uses Truchsess's I2C library for communication with the MPL3115A2 to avoid
the misaligned data bits caused by repeated-starts with the older Wire library.
Sampling when using the Wire library, <wire.h>, was found to be unreliable over time
Converted to use I2C library since it handles the repeated START I2C commands that the
Freescale, Inc., devices appear to use
Thanks to Wayne Truchsess for his excellent work on that system.
See http://dsscircuits.com/articles/86-articles/66-arduino-i2c-master-library
Written by HDTodd, July, 2015
Based on code by: A.Weiss, 7/17/2012, changes Nathan Seidle Sept 23rd, 2013 (SparkFun)
License: This code is public domain but you buy me (Seidle) a beer if you use this
and we meet someday (Beerware license).
Hardware Connections to MPL3115A2 (Breakoutboard to Arduino):
-VCC = 3.3V
-SDA = A4 Add 330 ohm resistor in series if using 5v VCC
-SCL = A5 Add 330 ohm resistor in series if using 5v VCC
-GND = GND
-INT pins can be left unconnected for this demo
Usage:
-Serial terminal at 9600bps
-Times various sensor measurements
-Monitors status flags used to poll device for data ready
During testing, GPS with 9 satellites reported 5393ft, sensor reported 5360ft
(delta of 33ft). Very close! (Seidle)
During testing in Bozeman, GPS with 9 satellites reported 1520m; sensor reported 1433m;
surprisingly far off (Todd)
*/
#include <I2C.h> // for IIC communication
#include "MPL3115A2.h"
#define MY_ALTITUDE 1520 // Set this to your actual GPS-verified altitude in meters if needed
// or set to 0 for no correction
uint8_t sampleRate=S_1; // We'll cycle through all 8 settings, but start with 1 sample/reading
MPL3115A2 thing; // This is the thing we'll be sampling
void setup()
{
Serial.begin(9600); // start serial for output
I2c.begin(); // join i2c bus
I2c.setSpeed(1); // go fast
thing = MPL3115A2();// create one
if (!thing.begin()) {
Serial.println("Can't init MPL3115A2!");
delay(1000);
exit(1);
}
// ALTITUDE CORRECTION (IF DESIRED)
// try with MY_ALTITUDE set to 0 and see if altimeter is
// accurate; if not, set MY_ALTITUDE to GPS-provided altitude in meters
if (MY_ALTITUDE != 0) thing.setAltitude(MY_ALTITUDE);
// And announce ourselves
Serial.println("Characterizing MPL3115A2 performance on an Arudino with access via I2C library");
Serial.println("Reporting value read and time to read (in msec) for 1..128 oversample counts");
}
void loop()
{
float altitude, pressure, temperature;
long startTime, inter;
int altTime, pressTime, tempTime, loopTime;
uint8_t count;
thing.setOversampleRate(sampleRate++); // Set the oversample rate for this set of readings,
// and cycle through all 8 possible settings
startTime = millis();
altitude = thing.readAltitude();
altTime = (int) ( ( inter=millis() ) - startTime );
pressure = thing.readPressure();
pressTime = (int) (millis() - inter);
inter = millis();
temperature = thing.readTemp();
tempTime = (int) (millis() - inter);
Serial.print("SampleCount = "); // Tell how many counts/sample
count = 1<<thing.getOversampleRate();
if (count < 10) Serial.print(" "); if (count<100) Serial.print(" ");
Serial.print(count);
Serial.print(" ");
Serial.print("Altitude: "); // Tell altitude & timing
Serial.print(altitude, 1);
Serial.print(" m [");
if (altTime < 10) Serial.print(" "); if (altTime<100) Serial.print(" ");
Serial.print(altTime);
Serial.print("ms] ");
Serial.print("Pressure: "); // Tell pressure & timing
Serial.print(pressure, 0);
Serial.print(" Pa [");
if (pressTime < 10) Serial.print(" "); if (pressTime<100) Serial.print(" ");
Serial.print(pressTime);
Serial.print("ms] ");
Serial.print("Temp: "); // Tell temperature & timing
Serial.print(temperature*1.80+32.0, 1);
Serial.print(" F = ");
Serial.print(temperature,1);
Serial.print(" C [");
if (tempTime < 10) Serial.print(" "); if (tempTime<100) Serial.print(" ");
Serial.print(tempTime);
Serial.print("ms] ");
loopTime = millis() - startTime; // Tell overall loop time (incl prints)
Serial.print("Loop time: ");
if (loopTime < 10) Serial.print(" "); if (loopTime<100) Serial.print(" ");
if (loopTime < 1000) Serial.print(" ");
Serial.print(loopTime);
Serial.println(" ms");
sampleRate %= 8; // repeat 0..7 in successive loops
delay(5000);
}
页:
[1]